5/7/18

DIY Wicker Roundie Bag from Placemats


Maybe this is just how my thrifty mind works but everytime I see those round wicker bags I think placemats! So I decided to go ahead and make my own trendy roundie using a set of placemats I got for a dollar each! I also wanted something with color instead of the typical natural to stand out a bit. To tie the overall finish together I needed to add some Dritz hardware. They really have everything you can think of when it come to making bags from fasteners to accents. For this bag I used the Small Swivel Hook & D-Ring set along with the Tassel Cap to add some more FUN (who doesn't love tassels?). These hardware details made all the difference in turning these placemats into a wicker worthy bag. 

Get the details below on how to make your own:



Supplies:




DIY Instructions:



Cut 2 rectangles of fabric that measure 4.5" x _. You will want to measure this according to the placemats you use. Make sure it's long enough to fit about 3/4 around the placemat.

Place the 2 rectangles right sides together, pin, and sew (1/4" seam allowance) around leaving a 2" gap about 2" in from one of the corners. 


Clip corners, flip right side out, and press.


Find midpoint of strip (fold in half) and place in the center of one of the placemats. Wrong sides together. 


Wrap around the placemat and pin as you go.


Sew into place right along the edge with a top stitch. My Brother sewing machine did not have a problem sewing the wicker material and I used a standard needle. 


Pin the other place mat on the alternate side and sew like before. 


You will have to position the materials like this to get them to sew around the other side properly. It takes a little maneuvering and lifting your presser foot up and down but it works just fine. 


For the Handles:
You can use fabric or leather for this. If using leather try Dritz Double-Cap Rivets and Double-Cap Rivet Tools

I wanted my handles to match the fabric around the bag. Make these straps to be long enough for a cross body bag or short enough to be a purse.



Cut 2 strips of fabric 1.5"x 12" (or your preferred length).

Fold the strips of fabric in half right sides together and sew along the edge.


Use a loop turner to flip right side out. 


Press so the seam is in the center back. Flip the end edges inside 1/4" and press. 


Position on the front of the bag so it's visually even. Pin into place. 


Top stitch the handles into place sewing a square or use rivets.


It takes a bit of Houdini sewing when working with a material like wicker but it works just fine.

Repeat for the back handles. 

Swivel Hook & D-Ring Closure:

Make another strip of fabric measuring 1"x 12" for your Swivel Hook and D Ring Closure. Again, fold in half right sides together, sew along the raw edges, and flip out with a loop turner. 
Press so center seam is in the back. 

Cut the strip into tabs. Make sure you can fold over the D-Ring nd Swivel hook and flip up another 1/2". Mine was about 3" long for the D-Ring and 5" long for the Swivel Hook.


Place tab with D-Ring so it's visually even on the front of the bag. Also make sure the Swivel Hook can fit around from the back before sewing and is positioned where you want it to be. 



Top stitch 2 rows along front tab/D-Ring.


Place and pin D-Ring with longer tab centered in the back between the handles (I didn't do my handles on the back yet at this point so pretend they're there). Sew 2 strips along bottom edge of tab and about 1/2" above (encasing the folded tab underneath).


Sewing the Swivel Hook tab. 


Now let's add a custom tassel while we're at it! 


Instructions:

  • Create a strip of fringe or use fringe trim
  • Roll up fringe and make sure it fits in the cap. Adjust if necessary. 
  • Unroll and place glue along top edge, tightly roll fringe into finished diameter.
  • Place a small amount of glue inside the tassel cap.
  • Insert rolled fringe into tassel cap.
  • Use a mini screw drive, insert the screws into the hole of the cap and screw. 


  • That's it! You now have your own wicker bag. I can't help but laugh when someone asks me where I go my bag? Oh, a set of placemats...

    *In collaboration with Dritz. 
    I received compensation from Dritz®, and some of the materials featured here or used in this project were provided free of charge by Dritz®. All opinions are my own.

    SaveSave

    15 comments:

    1. This is really clever. Wow! I hope that you'll make another, or something similar using leather and the double rivet tool.

      ReplyDelete
    2. wow! it's nice. i like it.

      ReplyDelete
    3. this is truly an amazing article, look so beautiful. wuxiaworld

      ReplyDelete
    4. Thanks for your post! I think there are many other people who are interested in them just like me! How long does it take to complete this article? I have read through other blogs, but they are cumbersome and confusing. I hope you continue to have such quality articles to share!

      ReplyDelete
    5. That's so special and adorable bag. I love this idea much.hotmail sign up

      ReplyDelete
    6. Through your pen I found the problem up interesting! I believe there are many other people who are interested in them just like me! How long does it take to complete this article? I hope you continue to have such quality articles to share with everyone! I believe a lot of people will be surprised to read this article!
      Hotmail.com
      Hotmail sign in
      Hotmail login
      Yahoo sign up

      ReplyDelete
    7. I like this bag. it's beautiful and different. but that circle. I like to hook with other material. Does it have a harder edge? nice looking bag for example. Can be variations to many other shapes. thank you for sharing.

      ReplyDelete
    8. The article you shared here is great. This is really interesting information for me. Thank you for sharing! microsoft office 2016 product key

      ReplyDelete
    9. The fashion accessories themselves are beautiful and unique

      ReplyDelete
    10. it’s great post.i learn something new.i’ll try it my own.
      hotmail sign in

      ReplyDelete